Steema Central

As far as I know I have installed TeeChart version 7 in Delphi 6 except for the decision cube. I don't use it anyway...

Cannot install a package that required TeeChart 5 (Tee56.dcp, etc are in the Requires group). I replaced all the TeeChart 5 references with TeeChart 7 references. But still gives error "Never-build package 'TeePro76' must be recompiled. I have tried setting the Build Control option to Rebuild as Needed, but not joy. By the way, I got an error like this when I tried to manually recomple the Decision Cube package.

Please help.

Thanks,

Rob

Hi Rob,

have you followed the correct installing order:

1) Uninstall old TeeChart version.
2) Install all Delphi 6 patches
3) Install TeeChart v7.02 for Delphi 6.

Yes, I followed the correct installing order. Like I said, TeeChart installed OK, but I was unable to use a custom package I made that required TeeChart 5. So, I uninstalled TeeChart that was installed via the binary installer, downloaded the latest source, and installed TeeChart 7 by way of building the packages. Everything worked fine until I restarted my computer. Now when I start Delphi I get this error:

"The procedure entry point @Teetml@initialization$qqrv could not be located in the dynamic link library Tee76.bpl."

I get this error each time Delphi tries to load a design time package.

All the runtime packages are in my C:\WinNT\System32 folder.

Thanks for your help.

Rob

I got everything working now.

I deleted all previous versions of the BPL files and ran TeeRecompile.exe.

All is well except no help files with the source. Maybe I can download from website.

Rob

After installing using binary install (to get the help files) I get "The procedure entry point @Teetml@initialization$qqrv could not be located in the dynamic link library Tee76.bpl," again.

I am now going to remove every thing that references TeeChar and the TeeChar runtime packages, re-install TeeChart 7 using the binary install, and hope and pray this works.

Any suggestions would be greatly appreciated.

Thanks,

Rob

I just upgraded to the TeeChart 7.02 from an earlier version and I'm getting the "Never Build Package Tee76 must be recompiled".

In my case, I find that if I eliminate all other components that use TeeChart (we have a couple with "Chart" in their uses statements) the problem goes away.

I've eliminated all the .dcu's, but I haven't tried the bpl's yet. If you find a solution (or if anyone else out there has any suggestions), please post!

I should have known better than to start this process right before vacation...

Rob, I used your comments and some experimentation to come up with a procedure that seemed to work:

1) Remove the components that use TChart. I also deleted the DCUs associated with them, but I don't know if that's necessary.
2) Shut down Delphi
3) Run the installation TeeChart7.01Delphi6.exe
4) Run the installation TeeChart7.02SourceCode.exe
5) Run the program TeeRecompile that is installed (by default) into:
"C:\Program Files\Steema Software\TeeChart Pro v7.02 Full Source Code"
6) Run Delphi
7) Re-install the components you removed in step 1.

However, I'm still encountering a very odd problem: When I try to run TeeChartOffice.exe, I get the message "The procedure entry point @Teetranslate@TeeTranslateAControl$qqrp17Controls@TControl could not be located in the dynamic link library TeeLanguage76.bpl" This also happens with "Tee7New.exe".

However, this hasn't happened with any of the programs that I've compiled.

So, for me, this is now more of a curiosity than a problem.

Hi Pat,

However, I'm still encountering a very odd problem: When I try to run TeeChartOffice.exe, I get the message "The procedure entry point @Teetranslate@TeeTranslateAControl$qqrp17Controls@TControl could not be located in the dynamic link library TeeLanguage76.bpl" This also happens with "Tee7New.exe".

Have you tried to recompile the TeeChartOffice sources and replace the old TeeChartOffice.exe file ?